If your robot is not navigating correctly, please refer to the error number reported by your robot. Otherwise, click on any of the possible contributing factors below for more details and the troubleshooting steps:
Cluttered Environments
For best results, ensure any clothing items, loose cables, toys, etc., are off the floor before cleaning, to allow for a successful cleaning job. Your robot will achieve its best results in an environment with minimal clutter.
Did you move any objects during the mission? If the robot bumps into an obstacle and then you move it, the robot will have no way of knowing, and this could affect its ability to enter that area.
Large Thresholds
Check for a physical barrier/transition that may be impeding Roomba® from entering a space. Sometimes Roomba can get over a gap one way, but can’t make it back over coming the other way. The maximum height of a threshold that all Roomba models can transition over, when performing a cleaning cycle, is ⅝ in (1.6 cm).
Thick Carpet
Some robots may have trouble with thick carpet, especially the s9 because the cleaning head sits lower to the ground. Longer rug threads and fibers could get too sucked up into the main brush, causing stalling or other navigation issues.
Check your care tags on your rugs and roll up or block off any thick carpeted areas.
Black or Dark Surfaces
Ensure the house has adequate light for the robot to navigate. Dark rooms can cause problems with navigation and coverage. Daylight or dim lighting is sufficient for Roomba® to navigate effectively.
Large Homes
If the space is larger than what Roomba can handle, the robot may not be able to cover the entire area and will need to be moved. You could use a keep-out zone or divider to separate a large space into two smaller maps.
Map Size Limit:
| Robot | Minimum | Maximum |
| j series | 4 ft² | 3,000 ft² (279 m²) |
| i6/7/8 | 4 ft² | 2,500 ft² (232 m²) |
| i3/4/5 | 4 ft² | 1600 ft² (148 m²) |
| s9 | 4 ft² | 2,500 ft² (232 m²) |
| m6 | 4 ft² | 2,500 ft² (232 m²) |
Low battery
Could the robot be going home to recharge mid-mission? When Roomba® senses that its battery is low, it will return to its dock to recharge. If there is more cleaning left to do, Roomba® will automatically continue its cleaning job after roughly 90 minutes of charging. When Roomba® is charging in the middle of a cleaning job, the CLEAN button will be pulsing when it is on the dock, and the (Classic) iRobot® HOME App will indicate that the cleaning job is paused.
Care and Maintenance
Lack of care for the robot can lead to all sorts of navigational issues. Be sure to clean the robot’s sensors regularly. They are in different places for each robot. The floor tracking sensor on the bottom of the robot must be cleared for proper navigation.
Turn Roomba® over to expose the iAdapt® Floor Tracking Sensor on the right side of the robot's bottom surface. To clean, use a dry microfiber or cotton cloth to wipe any debris that has accumulated. Do not spray cleaning solution directly into the sensor opening.
 |  |
| iAdapt® Floor Tracking Sensor |
 |  |
| iAdapt® localization camera |
Featureless Environments
No furniture, blank walls, ceilings that are all the same color, no windows. Roomba uses its environment to determine its precise location. If there are no defining features to the layout or design and every room looks exactly the same, Roomba may get confused.
Cleaning Preferences
Confirm you have given the robot the correct commands with the right settings. Cleaning preferences let you set the mission's parameters, such as the number of cleaning passes. Ensure you are selecting the rooms you’d like Roomba® to clean.
Bad/Corrupt Map (Smart Map robots only)
Check the map; perhaps it is corrupt or inaccurate.
-
- When did this behavior start?
- If the robot has never entered a certain area, this may be something in the environment.
- But if the robot used to clean a certain area and has recently started avoiding this same area, this could have something to do with your map.
Occasionally, the robot may make a mistake and update the map incorrectly. To bring your smart map to a previous version:
-
- Go into your "History" > select a "Clean Map® report" you like from a previous cleaning job > select the three dots in the top right corner > choose "Update Smart Map" to complete the process.
If this step is not helpful, the next best solution would be to delete your map and start over with a new one.
Infrared (IR) devices
- Are there any additional Infrared (IR) devices in the home, such as virtual reality headsets? These devices can interfere with robot signals and will need to be unplugged when the robot is cleaning. You will know this is the case if you see multiple docks appear on your map, such as the image below.

If you still aren’t sure why your robot may not be covering your entire home, it may help to understand how your robot navigates.
Navigation Types
| Adapt® 1.0 | iAdapt® 2.0 | iAdapt® 3.0 | LiDAR | Other |
| 400 Series | 900 Series | Combo® 10 Max | 100 / 1000 Series | i1, i2, i3, i4, i5 |
| 500 Series | Braava Jet | i Series (i6, i7, i8) | 200 / 2000 Series | Essential |
| 600 Series | - | j Series | Plus 400 Series | Essential 2 |
| 700 Series | - | s Series (s9) | Plus 500 Series | - |
| 800 Series | - | Braava m6 | Plus 600 Series
| - |
| e Series | - | - | Max 700 Series | - |
| - | - | - | Max 800 Series
| - |
| - | - | - | Mini | - |
Note: iAdapt® 1.0 – a.k.a., “random bounce”
Click on the navigation type to learn more.
iAdapt 1.0
Robots that use iAdapt® 1.0 Navigation Technology utilize a responsive algorithm to navigate the cleaning area. Instead of a systematic cleaning pattern of back and forth, Roomba® heads out to clean, and when it encounters an obstacle, it maps the location internally and then moves in another direction. Roomba® will continually clean and map in this fashion until the battery is low or there is no more new area to clean. Robots that utilize iAdapt® 1.0 do not have a Recharge and Resume feature, meaning the robot cleans as much of an area as possible on a single battery charge. The Roomba makes more than 60 decisions per second based on data from various sensors, allowing it to adapt to different situations.
iAdapt 1.0 relies on a suite of simple sensors to react to its environment. The system combines several basic navigation behaviors based on sensor feedback:
- Bump sensors: When the Roomba hits an obstacle, it changes direction at a new angle.
- Wall following: An edge sensor allows the robot to follow along the perimeter of a room.
- Dirt Detect: Acoustic and optical sensors help the robot identify areas with higher concentrations of dirt, prompting it to perform more focused cleaning in that spot.
- Cliff sensors: Infrared sensors prevent the robot from falling down stairs or other drop-offs.
- Spiraling: The robot can clean a concentrated area by moving in a spiral pattern.
No "Recharge and Resume": Because iAdapt 1.0 does not save a map of the cleaning area, the Roomba cannot resume a job after its battery runs low. Instead, it cleans as much as possible on a single charge.
Dock return: For charging, the robot looks for an infrared signal from its dock. If it was not originally started from the station, it will simply return to its original starting position.
iAdapt® 2.0
Cameras and vSLAM (Visual Simultaneous Localization and Mapping)
iRobot's iAdapt 2.0 is a navigation system that uses a top-mounted camera and sensors to help a Roomba robot vacuum systematically clean an entire floor of a home. The technology allows Roomba to clean in straight lines, back and forth; to mimic how you might actually vacuum your home. Roomba® divides your home into regions, and may leave an area or room before it completes cleaning. It will know where it left off and return to resume cleaning.
Example:

The system combines several key features to create a more comprehensive and efficient cleaning process:
vSLAM stand for Visual Simultaneous Localization and Mapping. Roomba uses a low-resolution camera on top of the robot to visually and continuously map its environment. The robot identifies distinct "visual landmarks", like furniture, lights, and windows, to determine its location and track areas it has already cleaned.
- Intelligent sensors: The system incorporates a full suite of sensors that adapt the cleaning pattern as needed. This allows the Roomba to navigate around furniture and clutter, get into corners, and clean along wall edges.
- Clean Map™ reports: After a cleaning job, the robot creates a "Clean Map™" that you can view in the (Classic) iRobot® HOME App. The map shows the areas that have been cleaned. However, the Roomba does not remember this map for future cleaning missions and creates a new one each time.
- Recharge and resume: If the Roomba's battery runs low during a cleaning cycle, it automatically returns to its dock to recharge. Once charged, it will resume cleaning where it left off to complete the job.
- Edge Clean: The robot periodically switches to an "Edge Clean" behavior to ensure that the edges along walls and furniture are thoroughly cleaned.
- Dirt Detect™: The Roomba uses optical and acoustic sensors to find dirtier areas and focuses extra cleaning effort on those spots.
iAdapt® 3.0
Introducing Smart Maps - “persistent mapping”
Like version 2.0, these robots also use vSLAM. Roomba uses a low-resolution camera on top of the robot to visually and continuously map its environment. The robot identifies distinct "visual landmarks", like furniture, lights, and windows, to determine its location and track areas it has already cleaned.
The robot's initial cleaning or mapping runs use vSLAM to generate a digital floor plan of your home. Once you have your Imprint Smart Map, you can use other features such as:
-
- Customize cleaning: Divide the map into distinct rooms, label them, and create specific cleaning zones for targeted cleaning.
- Control cleaning schedules: Instruct the robot to clean specific rooms or areas at certain times or on demand.
- Set keep-out zones: Draw virtual boundaries on the map to tell the robot where not to clean.
- Recharge and resume: If the robot's battery runs low during a cleaning job, it will automatically return to its base to recharge. Once charged, it resumes cleaning exactly where it left off.
- Imprint Link Technology: This feature allows a Roomba and Braava jet mop to communicate with each other. For example, a Roomba with Imprint Link can finish vacuuming, send a signal to a Braava jet, and the mop will automatically begin mopping the same area.
iAdapt® for i1, i2, i3, i4, i5
These models use a version of iAdapt with only "Clean Map™" capabilities. This is a report in the app that visually summarizes the areas cleaned, duration, coverage, and key events from a Roomba's cleaning session, but doesn't allow you to save the map.
Floor sensors enable the robot to navigate purposefully and in neat rows.
- Dirt Detect™ Technology: The i1 uses a piezoelectric sensor to detect concentrated areas of dirt. When it finds a dirty spot, it will focus its cleaning efforts there for a more thorough job.
- Optical encoders: Sensors in the wheels track the robot's movement and help it determine how far it has traveled.
Gyroscopic sensor and optical caster for Roomba® Essential Series
Gyroscopic sensor and optical caster
Roomba Essential use a combination of gyroscopic sensors and an optical caster wheel for movement, along with its physical bumper to navigate and clean in neat rows. Unlike more advanced models, it does not create a detailed map of your home but instead relies on its systematic approach and obstacle detection to clean efficiently. The Roomba Essential uses its sensors to identify landmarks, like a straight wall, to orient itself during a cleaning session.
- Bumper: A physical bumper on the front of the robot detects when it bumps into furniture or other objects, causing it to change direction.
- Cliff Sensors: Infrared sensors located underneath the robot detect ledges, preventing it from falling down stairs or other drop-offs.
- Optical Caster Wheel: This wheel helps the robot keep track of its position and direction during cleaning.
- Returning to the Dock: The robot is programmed to return to its charging dock when its battery is low or when cleaning is complete.
LiDAR
Newer 2025 model Roombas navigate using ClearView™ LiDAR technology to create a smart map of your home, enabling it to clean in organized, straight rows. After mapping, the robot uses this map to efficiently avoid obstacles, navigate your entire home in logical paths, and can clean in the dark. You can customize cleaning by setting up keep-out zones or selecting specific rooms through the (New) Roomba Home App.
If none of this was helpful, please contact iRobot Customer Care.
For expedited service, please have the following ready: