Installing the Rubber Seals onto your Roomba® Max 700 Combo Series Dock

Select your language below when installing the Rubber Seals onto your Roomba® Max 700 Combo Series Dock. 

• Dutch De rubberen afdichtingen aanbrengen op het dock van de Roomba® Max 700 Combo serie
• English (Canadian) Installing the Rubber Seals onto your Roomba® Max 700 Combo Series Dock
• English (UK) Installing the Rubber Seals onto your Roomba® Max 700 Combo Series Dock 
• French (Canadian) Installation des joints en caoutchouc sur la station de votre Roomba® série Max 700 Combo
• French Installer les joints en caoutchouc sur la base de votre Roomba® Max série 700 Combo
• German Gummidichtungen an das Dock deines Roomba® Roboters der Max 700 Combo-Serie
• Japanese Roomba® Max 700 Comboシリーズの充電ステーションへの密閉用ゴムの取り付け
• Portuguese (European) Instalar os vedantes de borracha na base Roomba® da série Max 700 Combo
• Russian Установка резиновых уплотнителей на док-станцию Roomba® серии Max 700 Combo
• Spanish Instalación de las juntas de goma en la base de Roomba® serie Max 700 Combo

We have identified an issue in some of the early production models of the Roomba® Max 700 Series Combo robots. But don’t worry, we have a quick fix. If you haven’t received a repair kit, please contact iRobot Customer Care.

What you will need: 

Caution – The repair kit contains small parts. Keep away from children and pets. 

• Repair Kit containing rubber seals   
  • 1 x Part #1 - light gray seal 
  • 1 x Part #2 - dark gray seal 
• Paper towels or a dry cloth  
• Flashlight (optional)

Installation Steps: 

1. Remove Roomba® from the dock. 
   
   
2. Hold the Power button on Roomba® for 10 seconds until the robot powers off. Set the robot aside. 
   
   
3. Remove both the clean and dirty water tanks from the dock. Set them aside. 
   
   
4. Unplug the power cord from the dock. 
   
   
5. With a paper towel or dry cloth, wipe down any dirt or water from the dock's overflow basin, where the robot typically rests.

6. Turn the dock over so it rests on its rear side, with the plug on the bottom.

7. Locate the two water transfer nozzles on the rear wall of the dock where the robot sits. 

• • Nozzle A – Clean water nozzle  
  • Nozzle B – Dirty water nozzle

8. Remove Part #1 (light gray seal) from the bag. Press the flat end of the seal towards the dock over upper nozzle A.  

• • Press the seal over the nozzle until it cannot move back any further. Rotate the seal while applying light pressure to ensure a secure fit.

9. Remove Part #2 (dark gray seal) from the bag. Press the flat end of the seal towards the dock over lower nozzle B. 

• • Press the seal over the nozzle until it cannot move back any farther. Rotate the seal while applying light pressure to ensure a secure fit.

10. Once complete, tilt the dock back to its normal upright position, place both the clean and dirty water tanks into the dock, and plug the power cord back in.  
    

11.  Place Roomba® back onto the dock. To ensure the robot is charging, wait for the dock’s light to pulse on and off. After 20 seconds, the dock should announce, “powering on, charging”. 
    
    
12.  Installation Complete! Roomba® is ready to continue cleaning. 

If you need additional help or have questions about the repair kit, please contact iRobot Customer Care.

We’re looking forward to talking to you. Sometimes life isn’t perfect, but your floors can be. Thank you for being a valued iRobot customer. 

For expedited service, please have the following ready:

• Your robot charged and with you
• Your robot's Serial number
• For warranty claims: Proof of purchase (receipt or invoice for purchase from an authorized retailer)